Guides · Bright Spark
Bright Spark: a guide to circuits and three stars
Bright Spark solves every circuit the way a real bench would, so the habits that earn three stars are the habits of a careful electrician. This guide covers both: how the stars work, and the electronics each chapter teaches, with the numbers the bench itself uses.
How the three stars work
The first star is for a bench that works. The goal is a list of checks, such as “with A on and B off, is the lamp lit?”, and each line ticks itself as you build, because the game solves the circuit in that situation without you flipping anything. A check also fails if anything is shorted or would burn out in that situation, so a circuit that works but cooks a part does not count. When every line passes, the bench is put through its checks on screen before the stars.
The second star is for nothing burnt on the way. A part pushed past its limit burns once it has stayed over it for a moment, so a blink is forgiven, but holding too much current through an LED is not. A burnt part can be tapped and fixed, but the middle star stays lost until you choose “Clear the bench and start again” from the menu and build it again.
The third star is for a tidy bench: no more wires than par, which is how many the game’s own answer lays. Every wire joins two neighbouring dots, so a run across four dots is three wires. Wires the bench came with that you could take up count against you too; the ones fixed in place do not. A part placed across a gap joins its two dots by itself, so put parts where they close the loop for you.
Hints cost nothing, and your best result on each bench is the one kept, so you can always go back for a missing star. There are 49 benches in 11 chapters, and the bench after the furthest one you have won is always open.
Ohm’s law with the bench’s own numbers
Three quantities do all the work. Volts are how hard the battery pushes, amps are how much current flows, and ohms are how hard a part makes it to flow. Ohm’s law ties them together: volts = amps × ohms, or turned round, amps = volts ÷ ohms.
The bench where you first choose a resistor is the clearest example. A red LED takes about 1.8 volts, so on the 9-volt battery the resistor has to take the other 7.2. An LED wants about 20 mA, which is 0.02 amps, so the resistor should be 7.2 ÷ 0.02 = 360 Ω. The nearest one on that bench is 330 Ω, and 7.2 ÷ 330 gives about 22 mA. The meter reads a little less, about 21, because a lit LED takes slightly more than its 1.8 volts once current flows.
Bulbs follow the same law. Every bulb on the bench draws 0.3 amps at its rated voltage, so a 3-volt bulb is 3 ÷ 0.3 = 10 Ω. Its brightness goes with the square of its share of that voltage: at half its volts it gives a quarter of its light, 25%, and the meter shows it.
Tap any part to put the meter on it. It shows the volts across the part and the current through it, and for a bulb how bright it is, for a motor how fast it turns, and for a battery the current it sends out. Read the meter before you change anything: the numbers say what the circuit is doing.
Series and parallel
Parts one after another in a single loop are in series. The same current goes through all of them, and they share the battery’s volts: two 3-volt bulbs in a row on a 3-volt battery get about 1.5 volts each and glow at about 25%. Unscrew either one and the loop is broken for both. Three 3-volt bulbs in a row on the 9-volt battery get about 3 volts each, which is how one battery runs bulbs made for less.
Parts side by side, each with its own path from + to −, are in parallel. Each gets the full battery voltage and each keeps working when another is taken out, which is how a house is wired. The battery sends out the sum of their currents, so two bulbs side by side draw twice what one does.
Switches follow the same pattern. Two switches in series make an AND: the current only gets through if both are closed. Two side by side make an OR: either one completes the loop. Cells in series add their volts when each one’s + meets the next one’s −: two 1.5-volt cells make 3 volts. Turn one round and it pushes against the other.
LEDs: which way round, and how much current
An LED lets current through one way only, in at its + leg, the longer one, and out at its − leg. In its symbol the triangle points the way the current flows and the bar is the − end. If an LED stays dark in a loop that should light it, tap it and turn it round before you look for anything else.
A lit LED has almost no resistance of its own, so straight across a battery it takes far too much current and burns out in a flash. On this bench an LED is lit from 1 mA, bright from 8, happiest at 20, and burns past 40. A resistor in the loop holds the current down: put it in before you close the loop, not after.
Each colour needs its own push before it lights at all: red about 1.8 volts, yellow 2.0, green 2.1 and blue 2.9. That is why LEDs side by side need a resistor each. Share one resistor between them and the red one, which needs the least voltage, takes all the current while the others stay dark. In a row it is the other way: one current runs through them all, so their voltages add up and one resistor does for the string. Red, yellow and green in a row take 5.9 volts, which leaves 3.1 of the 9 for the resistor.
Resistors: the colour code, and the watts
A resistor’s value is written in three coloured bands: two digits, then how many zeros to add. The colours run black 0, brown 1, red 2, orange 3, yellow 4, green 5, blue 6, violet 7, grey 8, white 9. So blue, grey, brown is 6, 8 and one zero: 680 Ω. Change only the third band and blue, grey, red is 6,800 Ω, ten times as much, so always read the third band twice.
Ohms are not the only thing a resistor has to be right for. Every part has a limit to the heat it can shed, and heat is watts: volts × amps. The small resistors on the bench are rated for a quarter of a watt and smoke at about twice that, 0.5 W. A 3-volt fan on a 9-volt battery leaves 6 volts for the dropper, and at the fan’s 0.3 amps that is about 1.8 watts, so a small resistor cooks while the big wire-wound dimmer, or two bulbs in a row, can take it.
Transistors: B, C and E
A transistor is a switch worked by electricity, with three legs. The middle one is B, the base. The top one is C, the collector, and the bottom one is E, the emitter. A small current flowing in at B and out at E switches on a much bigger current flowing in at C and out at E. So there are always two loops: a small one from + through a resistor into B and out of E to −, and a big one from + through the load into C and out of E.
The resistor in front of B sets how much goes in. From the 9-volt battery, B sits about 0.7 volts above E, so through 10 kΩ about (9 − 0.7) ÷ 10,000 = 0.83 mA flows into B. The transistor on the bench lets through up to 100 times what goes into B, about 83 mA, which is more than the LED’s resistor allows, so it switches fully on. Through 100 Ω, B would take over 50 mA and overheat; through 470 kΩ it gets a few hundredths of a milliamp and the LED barely glows. Never wire B without a resistor.
A transistor only works one way round. Upside down, with C below E, it passes almost nothing, so if a transistor circuit stays dark, check the letters on its legs. The meter on a transistor shows both loops: how much flows into B, and how much comes in at C.
Sensors, dividers and timers
The light sensor is a resistor that changes with light: 400 Ω in daylight and 40 kΩ in the dark. Put it in a row with a fixed resistor and the voltage at the point between them rises and falls with the light. That point goes to B, and the transistor switches on once it is above about 0.7 volts.
Which way up the pair goes decides everything. With the sensor at the bottom, in the dark it takes most of the volts, the point between them rises and the light comes on at night. With the sensor at the top it is the other way round, and the bottom resistor must be small: in the dark the sensor still lets a little through, and a large resistor at the bottom would let B creep up to its switching point.
A capacitor stores a little charge and gives it back when the battery is gone. Across an LED it keeps it glowing after the switch opens; feeding B through a resistor it holds a transistor on for a few seconds after a button is let go. More capacitance or more ohms, more seconds: that is how every simple timer is set. Never wire a capacitor straight into B.
Fault-finding with the meter
The call-out benches hand you something that has stopped, and the meter finds the fault faster than guessing. Measure across each part in turn. In a loop that is broken, every good part reads 0 volts across it and the open one reads the whole battery voltage, because the gap is where all the push is. A tight screw terminal reads 0 volts; a loose one reads the full 9 volts.
A dead bulb looks whole and cannot be mended, so it has to come off. A flat cell still reads 1.5 volts on its own, but it has 8 Ω inside, so measure the cells while the circuit is trying to run: under load the flat one reads next to nothing. A cell put in backwards takes away as much as it should give, so look at the + ends before you reach for the meter.
The rest are right parts in the wrong places: a light sensor and its resistor swapped, so the light comes on by day; the two wires between staircase switches joined together, so one switch stops mattering; a button across a buzzer instead of in its path, so the buzzer never stops and the button shorts the battery. A switch controls a part by being in its path, never across it.
Chapter by chapter
Each of the first six chapters teaches one idea and leans on the ones before. The last five put those ideas to work on faults to find and jobs around the house and the car.
- The loop (5 benches): a circuit is a closed loop, a switch opens and closes it, a short circuit skips the bulb, and metals conduct while rubber and plastic do not.
- Many paths (6 benches): series and parallel, switches as AND and OR, and bulbs in a row sharing a bigger battery.
- Volts and LEDs (6 benches): cells adding up, which way round an LED goes, why it needs a resistor, Ohm’s law to choose one, the colour code, and a resistor for each LED.
- Make it move (4 benches): a motor turns the way its current goes, a push button sounds a doorbell, a dimmer is a resistor you can turn, and two two-way switches make a staircase light.
- Transistors (5 benches): the transistor one leg at a time, then both loops and a button working B.
- Smart circuits (3 benches): a light sensor that switches on at night, a capacitor that keeps an LED glowing, and a tripwire alarm.
- Call-outs (7 benches): fault-finding with the meter, from a dead bulb to a doorbell fitted the wrong way.
- Around the house (3 benches): a fridge light on the contact the door switch leaves, a torch from the drawer, and a stairwell light that turns itself off.
- On the road (4 benches): jobs on a car at 12 volts, from dipped and main beam to reversing lights and a seat-belt warning, and a pair of switches that runs a model railway both ways.
- The workshop (2 benches): one resistor for a strip of LEDs in a row, and a dropper chosen for its watts as well as its ohms.
- Odd jobs (4 benches): a panic button in the alarm loop, a buzzer that wakes you at sunrise, a two-speed fan, and the extra volts a blue LED needs.
Questions
How do I get three stars in Bright Spark?
Make the bench work, burn nothing on the way, and lay no more wires than par. Every wire joins two neighbouring dots and counts as one, and a burn costs the middle star until you clear the bench from the menu and build it again. Hints cost nothing.
What resistor does an LED need on a 9-volt battery?
About 360 Ω for a red LED at 20 mA: the resistor takes the 7.2 volts the LED does not, and 7.2 ÷ 0.02 = 360. On the bench, 330 Ω gives about 21 mA and 470 Ω about 15 mA, both safe. Anything that lets more than 40 mA through burns the LED.
Which leg of a transistor is which?
B, the base, is the middle leg: a small current into it switches the transistor on. C, the collector, is the top leg, where the switched current comes in, and E, the emitter, is the bottom leg, where both currents leave towards −.
Why won’t my LED light in Bright Spark?
Most often it is the wrong way round: tap it and turn it round. Otherwise it may be sharing a resistor with a red LED that takes all the current, or, if it is blue, two cells and a resistor may not be enough: a blue LED needs about 2.9 volts before it lights at all, and a third cell gives it room.
How do you find a fault with a multimeter?
Measure the volts across each part while the circuit is switched on. In a broken loop the good parts read nothing across them and the open part reads the whole battery voltage. Test cells under load: a flat one still reads 1.5 volts on its own but next to nothing when it has to push a current.
