Guides · Wires
How to solve Wires
Every square in Wires has to be covered, and that one rule decides where every cable goes. Here are the habits that find the wiring, in the order that finds the most, with how the score works so you can go for three stars.
The rules, in one breath
Join every pair of matching terminals with a cable. A cable runs from square to square, across or down, never through a terminal that is not its own, and when you have finished no two cables share a square and every square on the board is covered. That last rule is the puzzle.
Boards are 6×6 with 4 pairs on Mondays and Tuesdays, 7×7 with 5 from Wednesday to Friday, and 8×8 with 6 at the weekend. The two terminals of a pair are never side by side. Any wiring that joins every pair and covers every square finishes the board.
Start where there is least choice
A square in the middle of the board has four neighbours, one on the edge has three, and a corner has two. A square that is not a terminal has a cable running in and out of it, so it uses two of its neighbours. A corner square therefore has no choice at all: a cable turns in it, and both its neighbours are on that cable.
When one of a corner’s two neighbours is a terminal, you know whose cable turns there and how it ends. The same reasoning works anywhere on the board: a terminal with only one free square beside it must run into that square, and an empty square with only two free neighbours is crossed by one cable that uses both. The boards pictured here are smaller than a real day’s, so the point is easy to see.
Never strand a square
The quickest route between two terminals is rarely the right one, because every square has to be covered: a short cable leaves squares behind, and often no other cable can reach them. Before you draw a cable, look at what it leaves.
A pocket of empty squares with no terminal in it can only be filled by a cable that goes in and comes out again, so it needs at least two open squares beside it. A pocket with one way in, or none, can never be filled, and the cable that made it has to go another way.
Cables are walls
On a finished board no cable crosses another, so a cable, or a chain of cables, that runs from one edge of the board to another splits it in two. Check both sides of it: each side must hold both terminals of every pair it holds one of. A cable that leaves two twins on opposite sides is wrong, however tidy it looks.
That is also how the long cables are found. The empty stretches of board still have to be covered, and only a cable that can reach a stretch without cutting another pair in two can do it. Ask, for each empty stretch, which pairs could run through it; often only one can.
What a finished board looks like
Every pair joined, every square covered, and no square used twice. Here cable 1 sets off away from its twin, loops down into the middle of the board and back up, and finishes through the corner, so that nothing is left behind.
Three stars: drags, time and hints
Par is one drag for each pair: 4 on the 6×6 boards, 5 on the 7×7 and 6 on the 8×8. Every cable you lay counts as a move when you let go, even one left short of its twin, and so does a tap on a terminal that pulls its cable out. Picking up a cable part-way along and carrying on is a new drag, and so is laying a cable again after another one has cut through it. Three stars needs par and no hints: every cable laid once, in one drag, and never touched again. Two stars allows one hint and a finish inside 3 minutes 45 seconds.
So plan the whole board before you draw anything. While your finger is still down nothing has been counted: back up along the cable you are drawing and it rubs itself out for free. Restart puts the board back as it was dealt and the count back to zero, but the clock keeps running.
The full speed bonus is for finishing inside 75 seconds, half the target time of 2 and a half minutes, and there is none after 5 minutes. Each hint costs 75 points and draws, faintly, the cable of the first pair not yet laid the way the board was built, route and all, for you to trace over. Tracing it is a drag like any other.
Questions
How do you solve Wires?
Start in the corners and along the edges, where squares have the fewest ways to be covered. Never lay a cable that leaves a pocket of squares no other cable can reach, or that puts two twins on opposite sides of it. Plan every cable before you draw, then draw each one once.
Do the cables in Wires have to cover every square?
Yes. That is the whole puzzle: the board is only finished when every pair is joined and every square is covered, which is why the short way between two terminals is usually the wrong one.
Can a Wires board be wired more than one way?
Any wiring that joins every pair and covers every square finishes the board, whether or not it is the one the board was built around. A hint follows the built one.
How do I get three stars in Wires?
Finish in par, one drag for each pair, without a hint. Every cable laid, redrawn or pulled out counts, so plan the whole board before you draw, and draw each cable once.
Can you lose at Wires?
No. A wrong cable costs the drag it took and nothing else. Taking longer costs the speed bonus, and extra drags cost the move bonus and the third star.
